Discovering Essential Plumbing Skills is Essential for Installing a Bathtub
Discovering Essential Plumbing Skills is Essential for Installing a Bathtub
Blog Article
What are your thoughts and feelings about Installing A Bathtub?
Setting up a bath tub isn't specifically rocket science, however it does need strong plumbing, carpentry, and also sometimes, tiling abilities. Changing an old bathtub with a new one is likewise a moderately tough task. If the old tub is readily easily accessible, the project can relocate immediately; if you need to open up a wall to remove the old bathtub and also place the brand-new tub, the task is a lot harder. In either instance, the project is within a residence handyman's skills, although you will require a helper to vacate the old bathtub as well as set in the new one. Make certain you have actually qualified on your own for the task and fit attempting it. Rather than hiring a specialist to take control of a halfway-completed project, it is much better to consider utilizing one before you start. Possibilities are you might need an expert plumber to make tube links.
This short article will certainly help you set up a brand-new bath tub in your shower room if you have currently acquired a brand-new bathtub and don't require to alter the plan of your previous water system pipes.
Your tools as well as material list must comprise the following:
Planning for the Setup
To start with, the supporting frame supplied with the bath needs to be fitted (if required) according to the maker's instructions. Next, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is necessary to make certain that if the tap comes with a plastic washer, it is fitted between the bathroom as well as the taps. On a plastic bathroom, it is also practical to fit a supporting plate under the faucets unit to prevent strain on the bathtub.
Fit the flexible tap connectors to the bottom of the two taps making use of 2 nuts and also olives (in some cases provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet through the hole in the bath. Make use of the nut provided by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make sure you utilize every one of the provided washing machines.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Link the bottom of the overflow tube in a similar manner.The bathroom need to currently prepare to be suited its last setting.
Removing Old Taps
If you need to change old taps with new ones as a part of your installation, after that the first thing you need to do is separate the water system. After doing so, activate the taps to drain any water staying in the system. The process of getting rid of the existing faucets can be rather bothersome as a result of the limited gain access to that is frequently the case.
Make use of a basin wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipes to the faucets. Have a fabric all set for the continuing to be water that will certainly come from the pipelines. Once the supply pipes have actually been removed, make use of the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to quit the solitary taps from turning throughout this process. When the faucets have been eliminated, the holes in the bath/basin will certainly need to be cleaned of any type of old securing substance.
Prior to proceeding to fit the new taps, contrast the pipeline links on the old faucets to the brand-new taps. If the old taps are longer than the new taps, after that a shank adapter is needed for the brand-new faucets to fit.
Mounting the Bath tub
Making use of both wood boards under its feet, position the bath tub in the called for placement. The wood boards are handy in equally spreading out the weight of the tub over the location of the boards rather than concentrating all the weight onto four little points.
The next objective is to make sure that the tub is leveled all round. This can be accomplished by checking the spirit level and also readjusting the feet on the bath tub till the spirit level reads degree.
To set up faucets, fit the bottom of the outermost versatile tap connector to the proper supply pipeline by making a compression sign up with; then do the same for the various other tap.
Turn on the water system and examine all joints and brand-new pipework for leaks as well as tighten them if necessary. Fill up the bathtub and likewise examine the overflow outlet as well as the regular outlet for leakages.
Finally, repair the bath paneling as defined in the manufacturer's instruction manual. Tiling and sealing around the bath tub should wait until the bathtub has been used a minimum of when as this will settle it right into its last setting.
Fitting New Taps
If the tails of the new faucets are plastic, after that you will need a plastic connector to prevent damage to the string. One end of the connector fits on the plastic tail of the tap as well as the various other end gives a link to the existing supply pipes.
If you require to fit a monobloc, then you will call for decreasing couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next off, position the faucet in the mounting hole in the bath/basin ensuring that the washing machines are in location between the tap and also the sink. Protect the faucet in place with the supplier provided backnut. When the faucet is firmly in place, the supply pipes can be attached to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with typical tap ports. The previous kind needs to be linked to the tap finishes initially, tightening only by hand. The supply pipes can later be connected to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Tiling Around the Bathtub
In the area where the bath satisfies the ceramic tile, it is necessary to seal the accompanies a silicone rubber caulking. This is necessary as the installation can move enough to split an inflexible seal, triggering the water to penetrate the wall in between the bathroom and also the tiling, resulting in problems with wetness as well as possible leakages to the ceiling listed below.
You can pick from a variety of coloured sealers to assimilate your fixtures and fittings. They are marketed in tubes and also cartridges, and also can sealing gaps as much as a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can load it with spins of drenched paper or soft rope. Remember to constantly fill the tub with water before securing, to enable the movement experienced when the tub remains in use. The sealant can split relatively early if you do not take into consideration this motion before sealing.
Additionally, ceramic coving or quadrant tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are likewise conveniently readily available on the marketplace. It is advisable to fit the tiles making use of water-resistant or waterproof sticky and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We hope you liked our article about Tools You Need to Install a New Bathtub . Thank you for finding the time to read through our piece. Loved our blog posting? Please share it. Help somebody else check it out. I recognize the value of reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Overflow resolution available. Report this page